Overview

General 2nd order filter designer with smoothing

Discussion

This module implements a general purpose second order filter that is capable of realizing many different filter types. The module performs internal smoothing allowing the filters to be updated without introducing clicks. In all cases, the module implements an underlying second order filter. First order filters are realized by setting some of the second order coefficients to zero.

The behavior of the filter is controlled by the filterType parameter. filterType is an integer in the range from 0 to 14 inclusive. After specifying filterType, set you adjust the filter parameters by setting the fields .gain, .freq, and .Q. Some filter types use only a subset of these parameters and ignore the others.

The following table discusses the various filter types and which variables are active in each case. The .freq variable controls the center frequency of the filter; .gain determines the boost or cut, in dB; .Q determines how sharp the filter is. Low .Q values lead to broad filters. High .Q values lead to narrow filters.

filterType = 0, Simple pass through with unity gain.

filterType = 1, Gain in dB [.gain].

filterType = 2, 1st order Butterworth low pass filter [.freq]

filterType = 3, 2nd order Butterworth low pass filter [.freq]

filterType = 4, 1st order Butterworth high pass filter [.freq]

filterType = 5, 2nd order Butterworth high pass filter [.freq]

filterType = 6, 1st order allpass filter [.freq]

filterType = 7, 2nd order allpass filter [.freq, .Q]

filterType = 8, 2nd order low shelf. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. [.freq, .gain].

filterType = 9, 2nd order low shelf w/Q. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. This module also has an adjustable Q parameter. [.freq, .gain, .Q].

filterType = 10, 2nd order high shelf. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. [.freq, .gain].

filterType = 11, 2nd order high shelf w/Q. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. This module also has an adjustable Q parameter. [.freq, .gain, .Q].

filterType = 12, 2nd order peaking filter. It has unity gain except around the specified frequency. By varying .gain, you can get a peak or a notch in the frequency band. [.freq, .gain, .Q].

filterType = 13, 2nd order notch filter. It has unity gain except around the specified frequency. At the specified frequency, the filter has a true notch with -inf dB gain. [.freq, .Q].

filterType = 14, 2nd order bandpass filter. It has unity gain at the specified frequency and falls off in both directions. The bandwidth of the filter is determined by Q. [.freq, .Q]

filterType = 15, 1st order Bessel low pass filter [.freq]

filterType = 16, 1st order Bessel low pass filter [.freq]

filterType = 17, 1st order asymmetrical low shelf [.freq, .gain]

filterType = 18, 1st order asymmetrical high shelf [.freq, .gain]

filterType = 19, 1st order symmetrical low shelf [.freq, .gain]

filterType = 20, 1st order symmetrical high shelf [.freq, .gain]

Type Definition

typedef struct _ModuleSofV2HpFract32
{
    ModuleInstanceDescriptor instance;            // Common Audio Weaver module instance structure
    INT32 filterType;                             // Selects the type of filter that is implemented by the module: Bypass=0 Gain=1 Butter1stLPF=2 Butter2ndLPF=3 Butter1stHPF=4 Butter2ndHPF=5 Allpass1st=6 Allpass2nd=7 Shelf2ndLow=8 Shelf2ndLowQ=9 Shelf2ndHigh=10 Shelf2ndHighQ=11 PeakEQ=12 Notch=13 Bandpass=14 Bessel1stLPF=15 Bessel1stHPF=16 AsymShelf1stLow=17 AsymShelf1stHigh=18 SymShelf1stLow=19 SymShelf1stHigh=20
    FLOAT32 freq;                                 // Cutoff frequency of the filter
    FLOAT32 gain;                                 // Amount of boost or cut to apply, in decibels (if applicable)
    FLOAT32 Q;                                    // Specifies the Q of the filter, if applicable
    FLOAT32 smoothingTime;                        // Time constant of the smoothing process
    INT32 updateActive;                           // Specifies whether the filter coefficients are updating (=1) or fixed (=0)
    fract32 smoothingCoeff;                       // Smoothing coefficient. This is computed based on the smoothingTime, sample rate, and block size of the module
    INT32 bShift;                                 // Number of bits to shift of Numerator coefficients
    INT32 aShift;                                 // Number of bits to shift of Denominator coefficients
    fract32* targetCoeffs;                        // Target coefficients in Fract32
    fract32* currentCoeffs;                       // Instantaneous coefficients in Fract32
    fract32* state;                               // State variables. 6 per channel.
} ModuleSofV2HpFract32Class;

Variables

Properties

Name	Type	Usage	isHidden	Default value	Range	Units
filterType	int	parameter	0	0	0:20
freq	float	parameter	0	250	10:0.1:20000	Hz
gain	float	parameter	0	0	-24:0.1:24	dB
Q	float	parameter	0	1	0:0.1:20
smoothingTime	float	parameter	0	10	0:1:1000	msec
updateActive	int	parameter	1	1	0:1
smoothingCoeff	fract32	derived	1	0.06449	Unrestricted
bShift	int	derived	1	1	Unrestricted
aShift	int	derived	1	0	Unrestricted
targetCoeffs	fract32*	derived	0	[5 x 1]	Unrestricted
currentCoeffs	fract32*	state	0	[5 x 1]	Unrestricted
state	fract32*	state	1	[6 x 1]	Unrestricted

Pins

Input Pins

Name: in

Description: audio input

Data type: fract32

Channel range: Unrestricted

Block size range: Unrestricted

Sample rate range: Unrestricted

Complex support: Real

Output Pins

Name: out

Description: audio output