Document toolboxDocument toolbox

(8.D.1.2) SOFControlFract32

Owned by Catherine Spain
Apr 10, 2023
6 min read

Overview

2nd order filter with coefficients derived from input pins

Discussion

This module implements a general purpose second order filter that is capable of realizing many different filter types. The module performs internal smoothing allowing the filters to be updated without introducing clicks. In all cases, the module implements an underlying second order filter. First order filters are realized by setting some of the second order coefficients to zero.

The behavior of the cascade filters are controlled by the filterType arrary. The variable, filterType is an integer in the range from 0 to 14 inclusive.

After specifying filterType, adjust the filter parameters by setting the fields, gain, freq, and Q. Some filter parameters are not applicable to all filter types. The variable, freq controls the center frequency of the filter, gain determines the boost or cut in dB, and Q determines how sharp the filter is. Low Q values lead to broad filters and high Q values lead to narrow filters.

The following table discusses the various filter types and which variables are active in each case.

filterType=0, Simple pass through with unity gain.

filterType=1, Linear gain. [gain].

filterType=2, 1st order Butterworth low pass filter. [freq].

filterType=3, 2nd order Butterworth low pass filter. [freq].

filterType=4, 1st order Butterworth high pass filter. [freq].

filterType=5, 2nd order Butterworth high pass filter. [freq].

filterType=6, 1st order allpass filter. [freq].

filterType=7, 2nd order allpass filter. [freq, Q].

filterType=8, 2nd order low shelf. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. [freq, gain].

filterType=9, 2nd order low shelf with Q. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. [freq, gain, Q].

filterType=10, 2nd order high shelf. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. [freq, gain].

filterType=11, 2nd order high shelf with Q. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. [freq, gain, Q].

filterType=12, 2nd order peaking filter. It has unity gain except around the specified frequency. By varying gain, you can get a peak or a notch in the frequency band. [freq, gain, Q].

filterType=13, 2nd order notch filter. It has unity gain except around the specified frequency. At the specified frequency, the filter has a true notch with -inf dB gain. [freq, Q].

filterType=14, 2nd order bandpass filter. It has unity gain at the specified frequency and falls off in both directions. The bandwidth of the filter is determined by Q. [freq, Q].

filterType=15, 1st order Bessel low pass filter. [freq].

filterType=16, 1st order Bessel high pass filter. [freq].

filterType=17, 1st order asymmetrical low shelf. [freq, gain].

filterType=18, 1st order asymmetrical high shelf. [freq, gain].

filterType=19, 1st order symmetrical low shelf. [freq, gain].

filterType=20, 1st order symmetrical high shelf. [freq, gain].

filterType=21, 2nd order Butterworth low pass filter with variable Q. [freq, Q].

filterType=22, 2nd order Butterworth high pass filter with variable Q. [freq, Q].

Type Definition

typedef struct _ModuleSOFControlFract32 { ModuleInstanceDescriptor instance; // Common Audio Weaver module instance structure INT32 filterType; // Selects the type of filter that is implemented by the module: Bypass=0, Gain=1, Butter1stLPF=2, Butter2ndLPF=3, Butter1stHPF=4, Butter2ndHPF=5, Allpass1st=6, Allpass2nd=7, Shelf2ndLow=8, Shelf2ndLowQ=9, Shelf2ndHigh=10, Shelf2ndHighQ=11, PeakEQ=12, Notch=13, Bandpass=14, Bessel1stLPF=15, Bessel1stHPF=16, AsymShelf1stLow=17, AsymShelf1stHigh=18, SymShelf1stLow=19, SymShelf1stHigh=20, VariableQLPF=21, VariableQHPF=22. FLOAT32 freq; // Cutoff frequency of the filter, in Hz. FLOAT32 gain; // Amount of boost or cut to apply, in dB if applicable. FLOAT32 Q; // Specifies the Q of the filter, if applicable. FLOAT32 smoothingTime; // Time constant of the smoothing process. INT32 postShift; // Number of bits to shift FLOAT32 coeffGain; // Scale coefficients based on postShift. INT32 updateActive; // Specifies whether the filter coefficients are updating (=1) or fixed (=0). fract32 smoothingCoeff; // Smoothing coefficient. This is computed based on the smoothingTime, sample rate, and block size of the module. UINT32 pinID; // Specifies which control pins are available. FLOAT32* coeffs; // Desired coefficients fract32* coeffsFract32; // Desired coefficients in fract32 fract32* current_coeffsFract32; // Instantaneous coefficients fract32* state; // State variables. 4 per channel. } ModuleSOFControlFract32Class;

Variables

Properties

Name

Type

Usage

isHidden

Default value

Range

Units

filterType

int

parameter

0

0

0:22

 

freq

float

state

0

250

10:20000

Hz

gain

float

state

0

0

-24:24

dB

Q

float

state

0

1

0:0.1:20

 

smoothingTime

float

parameter

0

10

0:1000

msec

postShift

int

parameter

0

4

0:1:24

 

coeffGain

float

derived

0

0.0625

Unrestricted

 

updateActive

int

parameter

1

1

0:1

 

smoothingCoeff

fract32

derived

1

0.06449

Unrestricted

 

pinID

uint

const

1

7

Unrestricted

 

coeffs

float*

derived

0

[5 x 1]

-10:10

linear

coeffsFract32

fract32*

derived

0

[5 x 1]

Unrestricted

 

current_coeffsFract32

fract32*

state

0

[5 x 1]

Unrestricted

 

state

fract32*

state

0

[4 x 1]

Unrestricted

 

Pins

Input Pins

Name: freqPin

Description: Cutoff frequency of the filter

Data type: float

Channel range: 1

Block size range: Unrestricted

Sample rate range: Unrestricted

Complex support: Real

 

Name: gainPin

Description: Gain of the filter

Data type: float

Channel range: 1

Block size range: Unrestricted

Sample rate range: Unrestricted

Complex support: Real

 

Name: qPin

Description: Q of the filter

Data type: float

Channel range: 1

Block size range: Unrestricted

Sample rate range: Unrestricted

Complex support: Real

 

Name: in

Description: audio input

Data type: fract32

Channel range: Unrestricted

Block size range: Unrestricted

Sample rate range: Unrestricted

Complex support: Real

Output Pins

Name: out

Description: audio output

Data type: fract32

MATLAB Usage

File Name: sof_control_fract32_module.m

M=sof_control_fract32_module(NAME, FREQPIN, GAINPIN, QPIN) Creates a general purpose second order filter that implements a number of standard filter types. The filter operates on multiple interleaved channels, with all channels being processed by the same set of coefficients. Arguments: NAME - name of the module. FREQPIN - Boolean that determines whether the module exposes an input pin that allows the frequency of the filter to be adjusted. GAINPIN - Boolean that determines whether the module exposes an input pin that allows the gain of the filter to be adjusted. QPIN - Boolean that determines whether the module exposes an input pin that allows the Q of the filter to be adjusted.

Â