Overview

Control signal operations module

Discussion

The module computes control operations (e.g. control signals from CAN) which are simple arithmetic operations using two input values. The module is controlled via the .packedConf array. The array size is numOps x 3 and there is a single row devoted to each operation:

Column 1 specifies what operation should be performed:

op=0, CONST 0 (out = 0).

op=1, CONST 1 (out = 1).

op=2, Pass through (out = in1).

op=3, Sum (out = in1 + in2).

op=4, Diff (out = in1 - in2).

op=5, Average (out = (in1 + in2) / 2).

op=6, Time Derivative (out = (in1[n] - in1[n-1]) * SR)

op=17, Multiplication (out = in1 * in2).

op=7, Division (out = in1 / in2).

op=8, Const Gain (if (in1 == 0) --> out = undb20("channelIndex2"), else out = undb20("-channelIndex2"))

op=18, Dynamic Gain (out = undb20(in1)).

op=9, Max (in1, in2)

op=10, Min (in1, in2)

op=11, Equal One Pass 2 (if (in1 == 1) --> out = in2, else out = 1)

op=12, Not Equal One Pass 2 (if (in1 != 1) --> out = in2, else out = 1)

op=13, Greater Than, (if (in1 >= in2) --> out = 1, else out = 0)

op=14, Boolean Invert (if (in1 < 0.5) --> out = 1, else out = 0)

op=15, FlipFlop1 - 1 for in1 = 1 until in2 = 1, else output 0

op=16, FlipFlop2 - 1 if in1 = 1 for sample count in in2, else output 0

Column 2 contains the channel index of the first input argument (0-based). Column 3 contains the channel index of the second input argument (0-based).

Example (sum): 0x01 00 03 = Ch 0 + Ch 1 = 65539. Example (sum): 0x00 01 03 = Ch 1 + Ch 0 = 259. Example (mul): 0x02 01 07 = Ch 1 * Ch 2 = 131335.

If an index is out of range or the op is out of range then the module outputs 0 for that operation.

This module supports only control data where block size is 1.

Type Definition

typedef struct _ModuleControlOp
{
    ModuleInstanceDescriptor instance;            // Common Audio Weaver module instance structure
    INT32 numOps;                                 // Number of operations to be computed
    INT32 numOpsPackedSize;                       // Size in 4 bytes packed for internal use
    INT32 updateActive;                           // Specifies whether the configuration is updating (=1) or fixed (=0).
    INT32* config;                                // Controls the operations. One row per op.
    INT32* packedConf;                            // Operations configuration with each row packed into a word.
    FLOAT32* lastValue;                           // Previous sample value on all input channels
    INT32* firstBlock;                            // Array of flags set on first block of each channel before lastValue is valid
    INT32* triggerPulse;                          // Array of flags set on in operation 16 to trigger pulse output
    INT32* prevTriggerState;                      // Array of flags set on in operation 16 to trigger pulse output
    INT32* outPulseCnt;                           // Array of pulse high period count in samples for operation 16
    INT32* triggerPulse2;                         // Array of flags set on in operation 15 to trigger pulse output
} ModuleControlOpClass;

Variables

Properties

Name	Type	Usage	isHidden	Default value	Range	Units
numOps	int	const	0	1	Unrestricted
numOpsPackedSize	int	const	0	1	Unrestricted
updateActive	int	parameter	1	1	0:1
config	int*	derived	0	[1 x 3]	Unrestricted
packedConf	int*	parameter	0	[1 x 1]	-2147483648:2147483647
lastValue	float*	state	1	[1 x 1]	Unrestricted
firstBlock	int*	state	1	[1 x 1]	Unrestricted
triggerPulse	int*	state	1	[1 x 1]	Unrestricted
prevTriggerState	int*	state	1	[1 x 1]	Unrestricted
outPulseCnt	int*	state	1	[1 x 1]	Unrestricted
triggerPulse2	int*	state	1	[1 x 1]	Unrestricted

Pins

Input Pins

Name: in

Description: Input signal

Data type: float

Channel range: Unrestricted

Block size range: 1

Sample rate range: Unrestricted

Complex support: Real

Output Pins

Name: out

Description: Output signal