Document toolboxDocument toolbox

SecondOrderFilterSmoothedCascadeV2

Overview

Cascade of second order filters realized as a single module

Discussion

This module implements a general purpose second order cascade filter that is capable of realizing many different filter types. The module performs internal smoothing allowing the filters to be updated without introducing clicks. In all cases, the module implements an underlying cascade second order filters. First order filters are realized by setting some of the second order coefficients to zero.

The behavior of the cascade filters are controlled by the filterType arrary. The variable, filterType is an integer in the range from 0 to 22 inclusive.

After specifying filterType, adjust the filter parameters by setting the fields, gain, freq, and Q. Some filter parameters are not applicable to all filter types. The variable, freq controls the center frequency of the filter, gain determines the boost or cut in dB, and Q determines how sharp the filter is. Low Q values lead to broad filters and high Q values lead to narrow filters.

The following list discusses the various filter types and which variables are active in each case.

filterType=0, Simple pass through with unity gain.

filterType=1, Linear gain. [gain].

filterType=2, 1st order Butterworth low pass filter. [freq].

filterType=3, 2nd order Butterworth low pass filter. [freq].

filterType=4, 1st order Butterworth high pass filter. [freq].

filterType=5, 2nd order Butterworth high pass filter. [freq].

filterType=6, 1st order allpass filter. [freq].

filterType=7, 2nd order allpass filter. [freq, Q].

filterType=8, 2nd order low shelf. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. [freq, gain].

filterType=9, 2nd order low shelf with Q. It allows you to vary the gain of the low frequencies. The high frequencies have a gain of 1.0. [freq, gain, Q].

filterType=10, 2nd order high shelf. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. [freq, gain].

filterType=11, 2nd order high shelf with Q. It allows you to vary the gain of the high frequencies. The low frequencies have a gain of 1.0. [freq, gain, Q].

filterType=12, 2nd order peaking filter. It has unity gain except around the specified frequency. By varying gain, you can get a peak or a notch in the frequency band. [freq, gain, Q].

filterType=13, 2nd order notch filter. It has unity gain except around the specified frequency. At the specified frequency, the filter has a true notch with -inf dB gain. [freq, Q].

filterType=14, 2nd order bandpass filter. It has unity gain at the specified frequency and falls off in both directions. The bandwidth of the filter is determined by Q. [freq, Q].

filterType=15, 1st order Bessel low pass filter. [freq].

filterType=16, 1st order Bessel low pass filter. [freq].

filterType=17, 1st order asymmetrical low shelf. [freq, gain].

filterType=18, 1st order asymmetrical high shelf. [freq, gain].

filterType=19, 1st order symmetrical low shelf. [freq, gain].

filterType=20, 1st order symmetrical high shelf. [freq, gain].

filterType=21, 2nd order Butterworth low pass filter with variable Q. [freq, Q].

filterType=22, 2nd order Butterworth high pass filter with variable Q. [freq, Q].

filterType=23, 2nd order Resonant bandpass filter. [freq, Q].

The hidden variable .bulkParamsUpdate can be used to control sofCoeffs calculation after all parameters are updated. This is useful when changing all four parameters, filterType, freq, gain and Q, simultaneously from host, to avoid intermediate coefficient transitions. Set this variable before writing filter parameters and then clear this after all filter parameters are updated.

On the ADI SHARC+ platforms, except ADSP-2157x and ADSP-2158x, the module make use of IIR Accelerators, in legacy mode, to optimize the processing time. The processing load is distributed as 1 channel processing in IIRA is equivalent to 2 channel core processing. i.e. the IIRA channels=floor(numChannels/3). As the accelerators access data by DMA, when the dm and pm caches are enabled, extra cycles are needed to maintain cache coherence. It is highly recommended to increase the allocation priority of this module instance in the signal flow to have a larger chance to allocate in the AWE fast heaps. In this way, the overhead from accelerator can be minimized. If any of this module instances allocated in the AWE slow heap, please note that the CPU load might be higher than without IIRA due to cache coherence maintenance. Maximum number of channels that can be processed in IIR Accelerator is limited to 32 and the remaining channels are processed by the core. i.e. IIRA channels=min(floor(numChannels/3), 32)

On the processors of 2159x where 8 IIR accelerators are available with dual SHARC+ cores, 4 IIR accelerators are statically reserved for each core. The processing load is distributed as IIRA channels = floorf(numChannels/3) * 2. i.e. if the numChannels are 10 then 6 channels are processed in 4 IIR accelerators in parallel with 4 channels in core processing. On SHARC+ processor, additional memory is allocated for accelerator TCB with size of numAcceleratorChannels*13. Also separate coefficient/state buffer is allocated as per the accelerator requirement.

Type Definition

typedef struct _ModuleSecondOrderFilterSmoothedCascadeV2 { ModuleInstanceDescriptor instance; // Common Audio Weaver module instance structure INT32 numStages; // Number of cascaded stages of the second order filter. FLOAT32 smoothingTime; // Time constant of the smoothing process. INT32 updateActive; // Specifies whether the filter coefficients are updating (=1) or fixed (=0). FLOAT32 smoothingCoeff; // Smoothing coefficient. This is computed based on the smoothingTime, sample rate, and block size of the module. INT32 bulkParamsUpdate; // State variable to handle bulk changes in parameters. INT32* filterType; // Selects the type of filter that is implemented by the module: Bypass=0, Gain=1, Butter1stLPF=2, Butter2ndLPF=3, Butter1stHPF=4, Butter2ndHPF=5, Allpass1st=6, Allpass2nd=7, Shelf2ndLow=8, Shelf2ndLowQ=9, Shelf2ndHigh=10, Shelf2ndHighQ=11, PeakEQ=12, Notch=13, Bandpass=14, Bessel1stLPF=15, Bessel1stHPF=16, AsymShelf1stLow=17, AsymShelf1stHigh=18, SymShelf1stLow=19, SymShelf1stHigh=20, VariableQLPF=21, VariableQHPF=22 Resonant=23. FLOAT32* freq; // Cutoff frequency of the filter, in Hz. FLOAT32* gain; // Amount of boost or cut to apply, in dB if applicable. FLOAT32* Q; // Specifies the Q of the filter, if applicable. FLOAT32* targetCoeffs; // Matrix of filter target coefficients. The size of the matrix is 5 x numStages. Each column contains the variables for a biquad arranged as [b0; b1; b2; a1; a2]. FLOAT32* currentCoeffs; // Matrix of filter current coefficients. The size of the matrix is 5 x numStages. Each column contains the variables for a biquad arranged as [b0; b1; b2; a1; a2]. FLOAT32* state; // State variables. 2*numChannels per section. void * hardware_specific_struct_pointer; // This is the internal array used for ADI IIR accelerator. Size is determined internally } ModuleSecondOrderFilterSmoothedCascadeV2Class;

Variables

Properties

Name

Type

Usage

isHidden

Default value

Range

Units

numStages

int

const

0

2

1:1:32

 

smoothingTime

float

parameter

0

10

0:1:1000

msec

updateActive

int

parameter

1

1

0:1

 

smoothingCoeff

float

derived

1

0.06449

Unrestricted

 

bulkParamsUpdate

int

state

1

0

Unrestricted

 

filterType

int*

parameter

0

[1 x 2]

0:23

 

freq

float*

parameter

0

[1 x 2]

10:0.1:23990

Hz

gain

float*

parameter

0

[1 x 2]

-24:0.1:24

dB

Q

float*

parameter

0

[1 x 2]

0:0.1:20

 

targetCoeffs

float*

derived

0

[5 x 2]

Unrestricted

 

currentCoeffs

float*

state

0

[5 x 2]

Unrestricted

 

state

float*

state

1

[2 x 2]

Unrestricted

 

hardware_specific_struct_pointer

void *

state

1

 

Unrestricted

 

Pins

Input Pins

Name: in

Description: audio input

Data type: float

Channel range: Unrestricted

Block size range: Unrestricted

Sample rate range: Unrestricted

Complex support: Real

Output Pins

Name: out

Description: audio output

Data type: float

MATLAB Usage

File Name: second_order_filter_cascade_v2_module.m

M=second_order_filter_cascade_v2_module(NAME, ISSMOOTH, NUMSTAGES) Creates a general purpose second order cascade filter that implements a number of standard filter types. The filter operates on multiple interleaved channels, with all channels being processed by the same set of coefficients. Arguments: NAME - name of the module. ISSMOOTH - optional argument which specifies whether the filter is smoothly updating. By default, ISSMOOTH=1. NUMSTAGES - number of second order filter stages.

Â